iLoud Micro Monitor 2: What Changed and Which Version to Buy

iLoud Micro Monitor 2 is the second generation of IK Multimedia's ultra-compact reference monitor. IK kept what worked in the original, the tiny footprint and a three-inch driver, and added three things: built-in ARC X room correction, a linear-phase crossover, and a new cabinet and driver design that reaches down to 40 Hz by the maker's figures. The official announcement is on 19 November 2026.

There is a second version too, the iLoud Micro Monitor 2 Upgrade: the same pair of speakers without the measurement microphone. Below I go through what actually changed, who should pick which version, and what to check before buying from a spec sheet alone.

The short version. Starting with a room that sounds random: iLoud Micro Monitor 2, microphone in the box. Already own an ARC microphone and you are a registered user of ARC, iLoud MTM, Micro Monitor Pro or Precision: Upgrade. Happy with the original Micro Monitor: no rush. One thing to check before you buy: the MM2 spec sheet lists no XLR input, which the first model had.

iLoud Micro Monitor 2 pair with the ARC measurement microphone on a white background

What changed from the original

The original iLoud Micro Monitor launched in 2016 and, according to IK, has sold more than 250,000 units. The second generation changes more than the photos suggest: a different woofer, a new tweeter with a waveguide, a linear-phase crossover and room correction inside the electronics. Every figure in the table is the manufacturer's: for the first model from IK Multimedia's product page, for the MM2 from IK's pre-launch press materials.

Spec iLoud Micro Monitor iLoud Micro Monitor 2
Drivers 3" woofer, 3/4" tweeter 3" composite-fibre woofer, 3/4" silk-dome tweeter with waveguide
Amplification Bi-amplified Class-D Four Class-D amplifiers, 50 W RMS, 70 W peak
Processing 56-bit DSP Digital linear-phase crossover, 2.75 kHz, 6th order
Frequency response 55 Hz to 20 kHz 49 Hz to 28 kHz, +/-2 dB; 40 Hz at -10 dB
Room correction Acoustic switches for desktop or shelf Built-in ARC X, profile stored in the speaker
Inputs Balanced XLR, RCA, Bluetooth RCA, USB-C, Bluetooth (AAC and SBC)
Mounting Isolation base, mic-stand thread Isolation tilt-base, 3/8" thread, wall and ceiling bracket compatible
Measurement mic in the box n/a yes (not in the Upgrade)

One honest note: two numbers in that table do not compare directly. The two models state maximum SPL by different methods (MM2: 94 dB continuous and 105 dB peak for the pair, ANSI-2034 pink noise), so I left it out of the table. For how to read this kind of data, see how to read a studio monitor's frequency response.

Built-in ARC X: the room becomes part of the speaker

This is the change with the biggest practical sense. You measure the room with the ARC microphone in the ARC X software, and the finished correction profile lands inside the speakers. After that the internal DSP does the work, with no extra hardware and no plugin in your DAW. IK adds a six-band EQ and emulation of well-known monitors and listening systems, so you can check how a mix will sound on something other than your desk.

The usual caveat, because every acoustician will tell you anyway: correction compensates for the room, it does not replace acoustics. It can flatten a response curve, not a slap echo off a bare wall behind you. Position the speakers sensibly before measuring, and our guide to studio monitor placement covers that.

Inside the ARC X ecosystem the MM2 can also work with iLoud Sub, ARC Studio and other iLoud speakers, in stereo, multichannel and immersive layouts. The software is sold separately as ARC X.

Bass and dispersion

A three-inch driver is a three-inch driver. Physics does not read brochures, but this design at least talks to it: IK moved to a long-throw composite-fibre woofer, a stiffer cabinet and a rear bass-reflex port. The result, by the maker's figure, is 40 Hz at -10 dB.

Close-up of the iLoud Micro Monitor 2 tweeter waveguide and woofer

My opinion, which I will stand by until we measure one: do not buy these for the 40 Hz number. Bass that is 10 dB down is still port-assisted bass, not a floor you can build a bass-heavy mix on. The real gain is elsewhere: the new tweeter waveguide matched to the woofer's dispersion. IK describes a wide sweet spot where the tone does not change as you move off-axis. On a small desk, with you leaning and standing, that matters more than another 9 Hz.

Linear phase in practice

The digital linear-phase crossover, carried over from the iLoud MTM MKII and Micro Monitor Pro, is meant to keep phase relationships between the drivers intact. In IK's spec the system stays coherent within +/-20 degrees from 220 Hz to 23 kHz. In practice that should mean a snare attack and a vocal position that do not smear as you shift in your chair. That is the maker's promise. Whether you hear it on a desk is checked with ears, not a spec sheet, so I will not say it is audible before I have heard it.

Inputs: USB-C, RCA and Bluetooth

The MM2 does not need an audio interface: one USB-C cable to your computer carries digital audio and ARC X control. For synths, a DJ mixer or an existing interface there are RCA inputs. Bluetooth (AAC and SBC) is for quick listening from a phone.

iLoud Micro Monitor 2 rear panel showing the volume knob, RCA inputs, USB-C port and link connector

Now the thing that is easy to miss. IK's MM2 spec lists RCA, USB-C and Bluetooth, and no XLR input, which the first Micro Monitor had. If you connect the speakers to an interface over a balanced cable and care about that path, check this before buying. I treat the pre-launch spec as valid, and I will compare it with the manufacturer's page after 19 November. For most desks it does not matter. For some signal chains it changes the answer.

Who it is for and what is in the box

IK aims the MM2 at producers and beatmakers in small studios, engineers who need a trusted second reference, content creators and podcasters with crowded desks, and listeners who want monitor accuracy with Bluetooth convenience. A practical size test: if your desk fits a laptop and a mug, it fits a pair of MM2s. For mounting there is a 3/8" mic-stand thread and compatibility with wall and ceiling brackets, so the speakers can go where there is no desk at all.

In the box: an active and a passive speaker, the ARC measurement microphone with a clamp (not in the Upgrade), a USB-C to USB-C cable, a two-metre speaker link cable, and a 24 V 2.5 A power supply with a mains cable.

MM2 or Upgrade

There is exactly one difference between the versions: the ARC measurement microphone. The standard iLoud Micro Monitor 2 has it in the box. The iLoud Micro Monitor 2 Upgrade is the pair without it. According to IK it is meant for registered users of ARC (any version with a microphone), iLoud MTM, Micro Monitor Pro or Precision, that is, people who already own a calibrated microphone.

iLoud Micro Monitor 2 pair seen from the front, without the measurement microphone, as in the Upgrade version

Rule of thumb: if you own an ARC microphone and a licence from that list, take the Upgrade, because a second measurement mic in a drawer is not a bonus. If you own nothing from that list, take the standard version, because measuring the room is the point of this generation. Without a measurement the speakers will play. With one they will tell you the truth about your room.

When to stay with the original and when to step up

The original iLoud Micro Monitor did not stop working because a second one exists. If you have used it for years, you rely on the XLR input the MM2 lacks, and you judge the room by ear, there is no reason to hurry. Switch when you miss room correction or consistent sound off-axis.

If the problem is small scale rather than the room, look one step up. The iLoud MTM MKII uses the same linear-phase thinking with larger drivers. And if you miss the low end but want to stay compact, IK pairs the MM2 with the iLoud Sub subwoofer in a 2.1 layout.

What we do not know

Every number in this guide comes from the manufacturer. We have no measurements of our own for the MM2 and we will not pretend otherwise. If the information released on 19 November differs from the materials we received earlier, I will correct the text. And since it comes up every time: room correction is no substitute for panels and bass traps when a room plainly sounds wrong, and a measurement mic will not fix a desk pushed against a wall.

Our showroom at Nowogrodzka 6A/102 is open Monday to Friday 10:00 to 19:00 and Saturday 12:00 to 17:00. Tell us which room you work in and what you record, and we will match a pair without piling on extras you do not need. Every product carries 36 months of warranty, and the 30-day Test-Drive covers equipment in the programme, so ask whether your pick is included. Phone: +48 573 580 840.

Straight answers

What is new in the iLoud Micro Monitor 2?

A new composite-fibre woofer, a tweeter with a waveguide, a digital linear-phase crossover and built-in ARC X room correction with the profile stored in the speaker. USB-C is new, and IK gives the frequency response as 49 Hz to 28 kHz +/-2 dB.

Does the iLoud Micro Monitor 2 have built-in room correction?

Yes. You measure the room with the ARC microphone in the ARC X software, and the profile stays in the speakers and runs on their DSP, even without a computer.

What is the difference between the Micro Monitor 2 and the Upgrade?

Only the measurement microphone: the standard version includes it, the Upgrade does not. According to IK the Upgrade is for registered users of ARC with a microphone, iLoud MTM, Micro Monitor Pro or Precision.

Does the iLoud Micro Monitor 2 have an XLR input?

IK's specification lists RCA, USB-C and Bluetooth inputs. The XLR input the first iLoud Micro Monitor had is not on that list.

Do I need an audio interface for the iLoud Micro Monitor 2?

Not for a computer: one USB-C cable carries digital audio and ARC X control. An interface helps when you want several sources over RCA.

How deep does the iLoud Micro Monitor 2 go?

By IK's figures the response is 49 Hz to 28 kHz +/-2 dB, and it reaches 40 Hz at -10 dB. Those are the manufacturer's numbers, not our measurements.

When is the official launch of the iLoud Micro Monitor 2?

19 November 2026. For current information on the product, see its page at Wired Tunes.

Three inches, room correction inside and one USB-C cable. If your room still sounds like a shoebox, come in before your mix ends up in one.

Read next

Back to top ↑