LEWITT LCT 440 PURE

LEWITT LCT 440 PURE is a large-diaphragm FET studio condenser microphone with a 1" true condenser capsule and a fixed cardioid polar pattern. LEWITT's bestselling model: no switches, no PAD, no onboard filters – the same capsule and circuit design as the higher-end LCT series models, stripped down to its essential form. Record-ready sound from the first take.

Same Capsule, No Unnecessary Controls

The LCT 440 PURE was built by removing everything that isn't required for a great recording. The 3 µm gold-sputtered 1" Mylar capsule is the same transducer found in LEWITT's more expensive LCT models – no mechanical or electronic compromises at the capsule level. The absence of PAD and low-cut filter switches is a deliberate design decision: the microphone handles up to 140 dBSPL without attenuation, and any low-frequency management happens at the interface or console. Self-noise of 7 dB(A) with a 133 dB(A) dynamic range covers the full range from quiet whisper-level sources to loud transient sources. A subtle lift around 4 kHz and 13 kHz adds natural presence and air to vocals and instruments – gentle enough not to sound harsh, pronounced enough to sit in a mix without extra EQ.

Compact Format and Camera-Friendly Design

At 138 × 52 × 36 mm the LCT 440 PURE is among the smallest large-diaphragm microphones in the LCT series. The compact profile and the absence of a bulky pop filter blocking the face make it practical for on-camera recording, streaming, and desktop podcast setups – the camera captures the performer, not just a microphone grille. The magnetic pop filter clips directly to the shockmount, requiring no separate stand. The set includes a shockmount, magnetic pop filter, foam windscreen, and a leather carrying pouch.

KEY FEATURES

• 1" true condenser capsule – the same transducer as in higher-end LCT models
• Polar pattern: cardioid (fixed, no switching)
• Self-noise: 7 dB(A)
• Maximum SPL: 140 dBSPL (0.5% THD) – no PAD needed
• Dynamic range: 133 dB(A)
• Subtle lift ~4 kHz and ~13 kHz – natural presence and air without harshness
• No PAD, no onboard low-cut filter – minimalist, zero-distraction design
• Compact format – practical for camera-facing and streaming setups
• Magnetic pop filter integrating directly with the shockmount
• Zinc die-cast housing, gold-plated 3-pin XLR connector
• Includes: shockmount, magnetic pop filter, windscreen, leather carrying pouch

TECHNICAL SPECIFICATIONS

• Transducer type: FET condenser, externally polarized
• Operating principle: pressure gradient transducer
• Diaphragm: 3 µm gold-sputtered Mylar, 25.4 mm (1")
• Polar pattern: cardioid
• Frequency range: 20 Hz – 20,000 Hz
• Sensitivity: 27.4 mV/Pa (–31.2 dBV/Pa)
• Self-noise: 7 dB(A)
• Maximum SPL (0.5% THD): 140 dBSPL
• Signal-to-noise ratio: 87 dB(A)
• Dynamic range: 133 dB(A)
• Attenuation pad: none
• Low-cut filter: none on body
• Internal impedance: 110 Ω
• Rated load impedance: 1,000 Ω
• Power supply: 48V phantom ±4V, 2.63 mA current draw
• Connector: gold-plated 3-pin XLR
• Enclosure: zinc die cast
• Dimensions: 138 × 52 × 36 mm (5.43" × 2.04" × 1.42")
• Weight: 310 g (10.9 oz)