LEWITT LCT 440 PURE is a large-diaphragm FET studio condenser microphone with a 1" true condenser capsule and a fixed cardioid polar pattern. LEWITT's bestselling model: no switches, no PAD, no onboard filters – the same capsule and circuit design as the higher-end LCT series models, stripped down to its essential form. Record-ready sound from the first take.
Same Capsule, No Unnecessary Controls
The LCT 440 PURE was built by removing everything that isn't required for a great recording. The 3 µm gold-sputtered 1" Mylar capsule is the same transducer found in LEWITT's more expensive LCT models – no mechanical or electronic compromises at the capsule level. The absence of PAD and low-cut filter switches is a deliberate design decision: the microphone handles up to 140 dBSPL without attenuation, and any low-frequency management happens at the interface or console. Self-noise of 7 dB(A) with a 133 dB(A) dynamic range covers the full range from quiet whisper-level sources to loud transient sources. A subtle lift around 4 kHz and 13 kHz adds natural presence and air to vocals and instruments – gentle enough not to sound harsh, pronounced enough to sit in a mix without extra EQ.
Compact Format and Camera-Friendly Design
At 138 × 52 × 36 mm the LCT 440 PURE is among the smallest large-diaphragm microphones in the LCT series. The compact profile and the absence of a bulky pop filter blocking the face make it practical for on-camera recording, streaming, and desktop podcast setups – the camera captures the performer, not just a microphone grille. The magnetic pop filter clips directly to the shockmount, requiring no separate stand. The set includes a shockmount, magnetic pop filter, foam windscreen, and a leather carrying pouch.
KEY FEATURES
- 1" true condenser capsule – the same transducer as in higher-end LCT models
- Polar pattern: cardioid (fixed, no switching)
- Self-noise: 7 dB(A)
- Maximum SPL: 140 dBSPL (0.5% THD) – no PAD needed
- Dynamic range: 133 dB(A)
- Subtle lift ~4 kHz and ~13 kHz – natural presence and air without harshness
- No PAD, no onboard low-cut filter – minimalist, zero-distraction design
- Compact format – practical for camera-facing and streaming setups
- Magnetic pop filter integrating directly with the shockmount
- Zinc die-cast housing, gold-plated 3-pin XLR connector
- Includes: shockmount, magnetic pop filter, windscreen, leather carrying pouch
TECHNICAL SPECIFICATIONS
- Transducer type: FET condenser, externally polarized
- Operating principle: pressure gradient transducer
- Diaphragm: 3 µm gold-sputtered Mylar, 25.4 mm (1")
- Polar pattern: cardioid
- Frequency range: 20 Hz – 20,000 Hz
- Sensitivity: 27.4 mV/Pa (–31.2 dBV/Pa)
- Self-noise: 7 dB(A)
- Maximum SPL (0.5% THD): 140 dBSPL
- Signal-to-noise ratio: 87 dB(A)
- Dynamic range: 133 dB(A)
- Attenuation pad: none
- Low-cut filter: none on body
- Internal impedance: 110 Ω
- Rated load impedance: 1,000 Ω
- Power supply: 48V phantom ±4V, 2.63 mA current draw
- Connector: gold-plated 3-pin XLR
- Enclosure: zinc die cast
- Dimensions: 138 × 52 × 36 mm (5.43" × 2.04" × 1.42")
- Weight: 310 g (10.9 oz)
